Classic British Flight Sim

Just bought vols 1 and 2 Ver 2.0...just wondering what you guys have as your settings to get the best from this cracking addon....looking for Vol 3 if anyone has a spare copy...

Tony

Hi Tony

I have v2 installed too and now have blocks of water around the coastline I never had with v1 but.. am I bovvered?? If you checkout the Horizon forums, I'm sure there's a note/post giving suggested/recommended settings. Alternatively, you should find em in the instructions

ATB

DaveB

Hi Mate, there was so good info in the readme about settings, but TBH I run my setting for overall experience not just for the GenX stuff. I'd imagine with a rig like yours you should be able to run it with most settings at or near max.

Tony, don't turn off autogen just because you can't see it. Turning autogen off only makes FSX performance worse not better (strange but true).

Regards,
Chris

Cheers Chris....was wondering about that...just experiment with the slider..? The manual says to switch it off...?

Tony

Tony,

This from a very long thread over on SimForums (the rest of the thread may be read here http://www.simforums.com/forums/forum_p ... ?TID=29041 :

"AUTOGEN #3:

FSX is strange when it comes to autogen simply because they have changed how it works 3 time now, from RTM to SP2

I can relay this advice:

One of the biggest mistakes people make is the thought that lower sliders = better perfomance. FSX is NOT a game, its a simulator and requires thinking a bit outside the box to tickle the hardware by the software settings and get it to run sweet

1. DO NOT use the autogen restriction lines in the configuration file for buildings and trees if you are using SP1/SP2. In most cases those lines will throw off the priority system and make the sim run/stutter worse.

2. Believe it or not, ZERO autogen slider can make frames drop, how? Same reason as above. Try to maintain at least 50+% (DENSE) however very slow systems may need to limit that to NORMAL/SPARCE or even OFF (off = rare must be very slow hardware)

Keeping the autogen slider at DENSE or greater actually tends to raise frames. Going too high for the installed hardware and Scenery Complexity/weather is where perf starts to really drop

Many can run a 3/4 (very Dense) Scenery Complexity with a 3/4 (very dense) autogen silder however your mileage may vary.

The important part about this slider is if your hardware is not very slow, keep it at a minimum of DENSE

This slider can also be changed mid-flight as well. There are times when you may fly out of a scenery friendly hub, into a very large urban area hub which may require this slider to be dropped a notch

Good systems can run 3/4 to 100% depending on the scenery involved and GEX USCAN can go a long way in helping with that performance. Autogen was laid out in a optimal way to reduce CPU overhead."

Tony, for what it's worth I run autogen at dense and get few or no stutters, whereas previously and with the same system I used to get very frequent stutters with autogen set to off. My system is based around an overclocked Q6600 (o/c'd to 3.24Ghz) with 4Mb of 1066Mhz RAM and an NVidia 9800 GTX+.

It's always worth experimenting in any event.

Regards,
Chris

Im trying to install Gen X to FSX but all the DVDs are not installing, all i get to is the setup screen, click on the FSX version to install then nothing, the setup screen disapears and nothing.

Any ideas...ive posted on the Horizon forum but no posts back yet.

Some early versions had a dodgy installer. My volume 1 would install OK, but vols 2 & 3 wouldn't. There are updated installers on Horizons site, although they are for version 1 only, so if you've got version 2 it doesn't really help.

Might also be a problem with your DVD reader...happened in the past to me with most things i tried to install...???

Any more problems or if you don't have any luck send the discs back and ask for fresh ones maybe...?

Tony